Window tint is a popular choice among automobile owners. So it is no surprise that many car owners today choose to tint their windows. The deep hues of tinted glass enhance a car’s appearance and can make a vehicle look posh and expensive.

The majority of people believe the tint covers the outside of the glass. They think it is probably because the outside of the window appears darker—this is not always the case.

This article explains where window tinting films are applied. It also describes how to use them on your car’s windows for the most satisfactory results.

 

Does Window Tint Go On The Inside Or Outside?

Typically, you apply a tinting film to the interior of the glass. You use a tinting film on the inside because installing the tinting film on the inside of a window protects it from harsh weather elements. These elements include the sun it might encounter when placed outside the car.

Using a tint film on the exterior is most commonly done before final installation. A tint installer may apply the film to the outside of the glass. Before placing the tint on the inside of the glass, the tint installer tests the film. The installer does this by measuring and cutting it to the proper size, so it fits the car window properly.

 

Why Is A Tint Applied On The Inside? 

The sun can damage human skin while you are inside your car driving. Window tint blocks 99% of the UV rays that come from the sun, resulting in a more comfortable interior temperature. The protection is just one of the critical advantages of car tint.

The tint is typically put on the inside as it works better when applied to the inside. The dark shade and properties of the film are more advantageous this way. Tint installers put it on the interiors over exteriors because;

1. Interior Protection

Tinting the inside of your car’s glass can stop the UV rays the sun produces from fading or damaging the leather on the vehicle’s interior. The interior of your car will remain stunning for a very long period.

2. Protection In Case Of An Accident

When tint installers place the window tint on your automobile’s interior, the film adheres to it. It has the power to hold broken glass together. In the event of an accident, this prevents glass fragments from injuring passengers or anyone around.

3. Improved Privacy

It becomes increasingly difficult for persons on the outside to peer through window films installed on the inside. Nasty people can not try to steal anything of value this way.

4. Higher Fuel Efficiency

You lose fuel efficiency each time you use your air conditioner. You can save money on fuel by placing window tints on the inside of your car, which will block the sun and chill the interior. It will reduce the need for an air conditioner.

5. More Comfort During Sweltering Months

By lowering sun glare, interior window tinting makes driving more comfortable for your eyes. It can assist in cooling the internal temperature of your automobile, causing the driver and passengers more comfort. It is essential during the warm summer months.

 

How To Tint Car Window Inside

If you want to tint the inside windows of your automobile but don’t know where to start, follow these simple procedures. The procedures are in two parts:

Getting The Window Tint Ready

• First, you must correctly size the tint. It would be best if you took measurements from the window’s exterior. Choose the adhesive-covered side of the tint film and turn it such that the sticky part is toward you.
• You should spray soapy water on the outside. It can temporarily secure the tint to the window and measure the tint sheet.
• Apply the tint to the moist window. Wait to remove the liner while you measure the tint film. Ensure there are at least 2-3 inches of tint film hanging over the borders of everything.
• Before cutting around the bottom and left borders of the glass, spray a slight coating of water on the exterior of the tint to cover the entire surface. When cutting, get as close to the edge as you can and make an effort to do it neatly.
• Draw the tint parallel to the freshly trimmed left edge. You can slightly adjust the tint film to ensure that it completely covers the window’s margins.
• After cutting the film on the right side, move the tint one-half inch to the right. It should add between a quarter-inch and a half-inch of the film.
• You should reduce the tint film by an inch. Rolling the window up and down will add some material to the bottom of the window.
• Lower the window just a little bit, then trim the top of the tint using it as a guide. Once you finish, pull the tint film back up toward the center to add more material to the top and bottom.
• After you smooth out any rough edges or unusual forms that have emerged during this process, move the tint back to the center. Moving the tint film back to the center should leave some extra material around all corners.
• Using a heat gun or hair dryer, work along the outside of the tint. With a stiff card, push the bubbles to the bottom. You will apply the tint to the interior of the glass, but you can temporarily leave it on the outside.

 

Putting the window tint on

• Moving inside, use soapy water to clean the glass and peel half of the liner away from the window tint. The sheet acts like a giant sticker, be careful not to rip the covering while peeling.
• Spray the exposed glue with soapy water and roll your window down carefully. Align the glass with the exposed adhesive side. The water you sprayed should help everything align.
• You may need to use your fingers to press the tint under the rubber seals surrounding the glass’s left and right sides.
• Spray the previously applied tint and squeegee or scrape the bubbles to the external edges. Remove the remainder of the sticky backing. Be cautious not to scratch the tint film.
• Lift the window and sprinkle the tint’s underside, then peel away the film’s adhesive backing.
• Push the film into the bottom edge of the pane seal with your fingers and a plastic or palette knife. To reattach the seal while folding the edge, you may have to use your fingers.
• Spray the entire area again and brush away any bubbles or excess water. Repeat till the tint is flat and appears to be completely adhered to the glass.
• Repeat the procedure for the next panels.

 

Is It Possible For The Tint To Be Applied From The Outside?

Tinting a car from the outside is achievable, but it may not be the most excellent decision for your vehicle. If the tint applied is too heavy, it might cause glare and limit visibility. Some individuals want the automobile’s inside to be as light as possible, making it easier to see inside. They also want it easy on their eyes. Applying tint film outside of some cars may also be a disadvantage. It is because the film can quickly become ruined or destroyed due to harsh weather conditions.

 

FAQs

Does the window tint get darker as it dries?

No matter what shade you choose, a tint film will always darken. When a tint begins to dry, the human eye perceives it as darker. It is not particularly visible.

What is the best tint for night driving?

The optimal tint shade for night driving is 20 percent tint. It is because it provides equilibrium both during the day and at night.

Do tinted windows affect visibility?

Only really dark tint films limit visibility while driving. Tints that decrease visibility are, in fact, illegal.

 

Conclusion

Now that you know where tint shades are applied and how to apply them, you can install one if you’ve been thinking about adding tint to your car windows. While tint films always go on the inside of a vehicle, you can also put them on the outside.

Putting them on the outside depends on your taste and ability to replace the tints when they deteriorate due to harsh weather conditions. There are a variety of tint shades to pick from, so choose the ideal one for you and enjoy your ride.